|
|
 |
 |
 |
 |
 |
|
Search this
site:
|
        |
|
Home
> LVDT Applications > Automation
Machinery
|
LVDT Products for Automation Applications
Below are LVDT products that are typically used in Automation Applications.
Spring-Loaded LVDTs are best suited, since the core and coil are assembled into a spring-loaded assembly. This makes the mechanical setup of the sensor into automated machinery less complicated and more cost effective.
When space is tight or the automated machinery configuration does not allow for Spring-loaded LVDTs the free core LVDT is to be considered. The hermetically sealed units are one of the more popular configurations used because of their construction and and connector configuration.
|
The
Macro Sensors GHSA 750 Series
of 3/4 inch diameter Spring-Loaded AC-LVDTs are designed for a
wide range of position measurement and dimensional gaging applications.
These rugged hermetically sealed sensors are constructed entirely of stainless
steel and intended for general industrial use. The coil windings are sealed
against hostile environments to IEC standard IP-68. Electrical termination
is through a sealed axial connector; the mating connector plug is supplied
with a unit. [read
more]
|
|
|
The
Macro Sensors GHSAR 750 Series
of 3/4 inch diameter Spring-Loaded AC-LVDTs are designed for a
wide range of position measurement and dimensional gaging applications.
These rugged hermetically sealed sensors are constructed entirely of stainless
steel and intended for general industrial use. The coil windings are sealed
against hostile environments to IEC standard IP-68. Electrical termination
is through a radially mounted sealed connector, which results in a much
reduced installed length. The mating connector plug is supplied with a
unit. The through-bore design allows for air purging of the sensor’s
bearings to remove potential contaminants. [read
more]
|
|
|
The
GSA 750 Series of short range
Spring-Loaded LVDT position sensors were developed for cost sensitive
applications requiring LVDT reliability and performance. Available in
ranges of ±0.10 inches to ±0.30 inches, these sensors offer
the excellent measurement capabilities of an LVDT at very economical prices.
This makes GSA 750 series LVDTs especially attractive for student projects,
low over-head machine and fabrication shops, and R & D laboratories
on a limited budget. [read
more]
|
|
|
The
Macro Sensors GHSE 750 Series
of 3/4 inch diameter spring-loaded DC-LVDTs are designed for a wide range
of position measurement and dimensional gaging applications. These rugged
hermetically sealed sensors are constructed entirely of stainless steel
and intended for general industrial use.... [read
more]
|
|
|
The
Macro Sensors GHSER 750 Series
of 3/4 inch diameter spring-loaded DC-LVDTs are designed for a wide range
of position measurement and dimensional gaging applications. These rugged
hermetically sealed sensors are constructed entirely of stainless steel
and intended for general industrial use.... [read
more]
|
|
|
The
GHSI Series of Spring-Loaded
DC-Operated LVDTs offer all of the advantages of the GHSD 750 series
with 2-wire, loop-powered 4-20 mA operation. They feature spring extended
plungers guided by precision sleeve bearings, and in-line electrical connectors.
The coil and electronics are hermetically sealed against hostile environments.
[read
mo
|
|
|
The
GHSIR Series of Spring-Loaded
DC-Operated LVDTs offer all of the advantages of the GHSD 750 series
with the added benefit of 2-wire, loop-powered 4-20 mA operation and a
radial connector that pemits a much shorter installed length. The coil
and electronics are hermetically sealed against hostile environments.
[read
more]
|
|
|
Macro
Sensors’ HSA 750 Series
of 3/4 inch (19 mm) diameter AC-Operated LVDTs is designed for
a wide range of position measurement applications. These are rugged hermetically
sealed sensors, constructed entirely of stainless steel, and intended
for general industrial use. The coil windings are sealed against hostile
environments to IEC standard IP-68 and electrical termination is through
a sealed axial connector. The mating connector plug is supplied with the
unit. [read
more]
|
|
|
The
HSTA 750 Series of 3/4 inch
(19 mm) diameter AC-operated LVDTs is designed for a wide range of position
measurement applications. These are rugged hermetically sealed sensors,
constructed entirely of stainless steel, and intended for use at high
temperatures (400°F) or exposed to mild radiation (3x107 Rads for
40 years). The coil windings are sealed against hostile environments to
IEC standard IP-68 and electrical termination is through a sealed axial
connector. The mating connector plug is .... [read
more]
|
|
|
Macro
Sensors’ HSAR 750 Series
of 3/4 inch (19 mm) diameter AC-Operated LVDTs is designed for
a wide range of position measurement applications. These are rugged hermetically
sealed sensors, constructed entirely of stainless steel, and intended
for general industrial use. The coil windings are sealed against hostile
environments to IEC standard IP-68 and electrical termination is through
a sealed radial connector located near one end. The mating connector plug
is supplied with the unit. [read
more]
|
|
|
The
HSTAR 750 Series of 3/4 inch
(19 mm) diameter AC-operated LVDTs is designed for a wide range of position
measurement applications. These are rugged hermetically sealed sensors,
constructed entirely of stainless steel, and intended for use at high
temperatures (400°F) or exposed to mild radiation (3x107 Rads for
40 years). The coil windings are sealed against hostile environments to
IEC standard ... [read
more]
|
|
|
The
Macro Sensors BBP
family of 8 mm diameter pencil-type gaging probes offers ultra-precise
measurement of dimensions in a wide variety of Q.C., SPC, and industrial
metrology applications. They utilize a linear ball bearing assembly precisely
fitted to a hardened-and-ground, non-rotating probe shaft to minimize
radial play and the effects of side loading. This results in the probes'
exceptional repeatability of 0.000006 inch (0.15 µm). [read
more]
|
|
|
The
Macro Sensors BBP
and BBT family of 3/8 inch diameter pencil-type gaging probes offers
ultra-precise measurement of dimensions in a wide variety of Q.C., SPC,
and industrial metrology applications. They utilize a linear ball bearing
assembly precisely fitted to a hardened-and-ground, non-rotating probe
shaft to minimize radial play and the effects of side loading. This results
in the probes' exceptional repeatability of 0.000006 inch (0.15 µm).
[read
more]
|
|
|
The
DMC-A2
is an accurate, high performance, programmable dual channel controller
that delivers precise measurement and control for applications using LVDT
(Linear Variable Differential Transformer) inputs. The 6-digit alphanumeric
LED display provides easy to follow setup prompts for all LVDT parameters
using the intuitive scrolling text configuration menus. [read
more]
|
|
|
The
DMI-A1
is an accurate, high performance, programmable single channel LVDT indicator
that delivers precise measurement for applications using LVDT (Linear
Variable Differential Transformer) inputs. The 5-digit alphanumeric LED
display provides easy to follow setup prompts for all LVDT parameters
using the intuitive text configuration menus. [read
more]
|
|
|
The
DMC-D2
is an accurate, high performance, programmable Dual Channel Controller
that delivers precise measurement and control for applications using
DC LVDT (Linear Variable Differential Transformer) inputs. The 6-digit
alphanumeric LED display provides easy to follow setup prompts for all
DC LVDT parameters using the intuitive scrolling text configuration menus.
[read
more]
|
|
|
The
DMI-D1
is an accurate, high performance, programmable single channel DC LVDT
Indicator that delivers precise measurement for applications using
DC LVDT (Linear Variable Differential Transformer) inputs. The 5-digit
alphanumeric LED display provides easy to follow setup prompts for all
LVDT parameters using the intuitive text configuration menus [read
more]
|
|
|
Prepared by Harold Schaevitz
|
|
|
|
|